Flat dimensions with<br>four mounting screws

Flat dimensions with
four mounting screws

Strain sensor X-103-8

Area: 0-360 µm/m
Size: 93x25x13
Notes: ± 10 V or 4-20 mA
With external input for automatic zero-point adjustments

Strain sensor X-103-8

Strain sensors for dynamic applications, with Process-Zero (cyclic)

  • Analogue signal path with fast response time
  • For dynamic applications with external input for automatic zero-point adjustments, qualified for periodical and recurring zero point adjustment
  • For indirect force and deformation measurements
  • With integrated amplifier with ± 10 V or 4-20 mA

Applications

Dynamic applications describe recurring, fast measurement cycles, as usually found in presses. In cyclic applications, it is important that the zero point is tared in regular intervals in order to minimize drifting of the measuring signal.

The strain sensors can be used for the following applications:

  • Indirect force measurement by detecting smallest strains allows efficient control of relevant process parameters (e.g., presses, assembly machines, welding machines, jigs, feed force)
  • Limit value monitoring to avoid overloads
  • Monitoring and documentation of process forces for increased process reliability (eg joining forces, assembly machines, pressing force, detection of tool breakage and wear)

The strain sensors from X-Sensors reliably measure even smallest strains on the surface of flat structures. Thanks to the strong and simple screw-on mounting, the measured values are more than comparable to glued strain gauges. Even more, because of the protecting housing, disadvantages of glued strain gauges are avoided. Thanks to the integrated, extremely low-noise and highly stable signal amplifier, the sensors have an enormous dynamic range.

Functionality

The surface strain sensor X-103-8 monitors the strain between its two mounting screws and amplifies this mechanically. In this way the strain is concentrated in the measuring area and can therefore be measured using a resistive strain gauge bridge. The integrated amplifier provides a signal conditioning and delivers a linear, robust output signal. The solid steel housing and the robust design (IP64) guarantee problem-free operation, even under difficult environmental conditions.

Zero point adjustment

The zero point adjustment at these strain sensors is carried out by a digital zero adjustment mechanism. The zero point adjustment is not stored permanently, it is lost after a power off. It provides a non-volatile, stable zero point independent of cycle times. Therefore, it is qualified for all dynamic applications and can be used in all kind applications which require a periodical zero point reset, triggered by a digital input.

The reset input does trigger a zero point adjustment by the PLC. It is available with an “Active Low” and “Active High” Logic.

Downloads

Data sheet – Strain sensor for dynamic applications – DigTara

X-103-8 3D-Step Datei

X-103-8 3D-Step Datei (M12)



Scope of application


Strain sensor with scalable measuring range
Strain sensors with switchable measuring range are very flexible and universally applicable for different nominal strain ranges.

The option "switchable measuring range" was specially designed for a wide range of application covering: Four pre-calibrated measuring ranges (62.5 μm/m, 125 μm/m, 250 μm/m, 500 μm/m) can be selected with a digital input. mehr


Zero point adjustment of strain sensors
Installation-Zero und Process-Zero - Zero point adjustment of strain sensors at X-Sensors mehr



Strain sensor X-103-8

Unverbindliche Anfrage stellen

Bitte senden Sie mir ein Angebot für folgendes Produkt: Strain sensor X-103-8.

Ich beabsichtige dieses Produkt in folgender Anwendung einzusetzen:

This contact form is deactivated because you refused to accept Google reCaptcha service which is necessary to validate any messages sent by the form.

Schnellanfrage stellen

Schreiben Sie uns – Wir rufen Sie auch gerne zurück! Wir beantworten Ihnen gerne alle Fragen zu unseren Produkten.

    Ihr Name*

    Ihr Vorname*

    Firma

    Telefon

    PLZ*

    Ihre E-Mail*

    Ihre Nachricht

    Bitte rufen Sie mich zurück

    Patrick Bernauer

    Patrick Bernauer

    Verkauf Endkunden / Distributoren
    Tel.: +41 52 543 19 66
    E-Mail: sales@x-sensors.com

    Bei Fragen zu unseren Produkten stehe ich Ihnen gerne zur Verfügung.

    sales@x-sensors.com
    +41 52 543 19 66

    Related products/accessories

    You need help for selecting the right sensor?
    Please get in touch with us!

      Your Name/Surname*

      Company

      Your E-Mail*

      Patrick Bernauer
      Sales & Technical Support

      Tel.: +41 52 543 19 66
      E-Mail: sales@x-sensors.com

      Your message

      Please call me back